1. PEMBUKAAN PAINPOINT DRIVEN

Are you managing unpredictable maintenance cycles, penggunaan tenaga yang berlebihan bagi setiap tan klinker, or unplanned downtime that halts your entire production line? In cement plant operations, equipment failure isn't just a repair ticket; it's a direct hit to your bottom line. Unplanned stoppages can cost tens of thousands of dollars per hour in lost production and emergency labor. Are you constantly balancing the high capital cost of premium equipment against the recurring expenses and risks of unreliable machinery? What if your key plant equipment offered not just durability, but predictable performance and measurable efficiency gains? The solution lies in specifying engineered Peralatan Loji Simen designed from the ground up for the extreme demands of pyroprocessing and raw material handling.

2. GAMBARAN KESELURUHAN PRODUK

This product category encompasses heavyduty, engineered machinery central to cement production, specifically focusing on Cement Mill Separators dan HighEfficiency Cyclone Preheaters. These are not commodity items but precisionengineered systems that define your plant’s thermal and grinding efficiency.

Aliran Kerja Operasi:
1. Raw Meal Processing: Prepared raw meal is fed into the multistage cyclone preheater string.
2. Heat Exchange & Precalcination: Gassolid heat exchange occurs in cyclones; calcination begins in the precalciner (associated system).
3. Clinker Grinding: Resulting clinker is cooled and fed into the cement mill.
4. Pengelasan Zarah: Within the closedcircuit mill, the separator dynamically classifies fine product from coarse material.
5. Koleksi Produk: Finished cement is conveyed to storage, while coarse material is recirculated for further grinding.

Skop Permohonan & Batasan: This equipment is designed for integrated cement plants and large grinding stations. Optimal performance is contingent on proper system integration, consistent feed quality, dan pematuhan kepada jadual penyelenggaraan yang ditetapkan. It is not suitable for batch processes or very smallscale (sub500 TPD) operations without significant customization.

3. CIRI TERAS

Dynamic Rotor Separator | Asas Teknikal: Adjustable rotor speed & guide vane angle control | Faedah Operasi: Realtime fineness control (Luas permukaan Blaine) without stopping mill operation | Kesan ROI: Hingga 8% pengurangan penggunaan tenaga tertentu (kWj/t) by optimizing recirculation load.

Reka Bentuk Siklon Penurunan Tekanan Rendah | Asas Teknikal: Dinamik Bendalir Pengiraan (Cfd)optimized geometry and inlet volute | Faedah Operasi: Reduces fan power demand and overall system pressure drop | Kesan ROI: Cuts ID fan energy use by 1015%, secara langsung menurunkan kos operasi setiap tan.

WearResistant Lining Systems | Asas Teknikal: Modular ceramiccomposite or hardened steel plates with strategic thickness | Faedah Operasi: Extends service life in highabrasion zones (kilang mentah, clinker cooler ducts) | Kesan ROI: Reduces annual lining replacement costs by up to 40% dan masa henti yang berkaitan.

Pelabuhan Pemantauan Keadaan Bersepadu | Asas Teknikal: Preinstalled sensor mounts and inspection hatches at critical wear points | Faedah Operasi: Enables predictive maintenance through vibration, suhu, and acoustic emission tracking | Kesan ROI: Mengubah penyelenggaraan daripada berasaskan kalendar kepada berasaskan keadaan, mencegah kegagalan bencana.

Optimized Gas Flow Path | Asas Teknikal: Aerodynamically smooth transitions and minimized internal obstructions | Faedah Operasi: Reduces particle dropout and buildup, maintaining design efficiency over longer campaigns | Kesan ROI: Improves operational stability and reduces need for offline cleaning shutdowns.

4. KELEBIHAN KOMPETITIF

| Metrik Prestasi | Piawaian Industri | Cement Plant Equipment Solution | Kelebihan (% penambahbaikan) |
| : | : | : | : |
| Penggunaan Kuasa Khusus (Separator) | 68 kWh/t cement | 5.26 kWh/t cement | Hingga 15% pengurangan |
| Kecekapan Pengumpulan Siklon (>30m) | ~85% nominal efficiency at design point |>92% across a range of gas loads| ~8% improvement |
| Purata Masa Antara Penyelenggaraan (MTBM) Bahagian Pakai Kritikal| ~12 months based on scheduled intervals |>18 months via predictive monitoring & bahan| ~50% increase |
| Particle Size Distribution Control (Separator)| Manual adjustment during shutdowns| Online adjustment via PLC during operation| Allows realtime product grade changes |

5. SPESIFIKASI TEKNIKAL

Kapasiti/Penilaian: Separators rated for mill outputs from 50 tph sampai habis 250 tph; Cyclone stages designed for kiln gas flows from 150,000 Nm³/h upwards.
Keperluan kuasa: Memandu motor dari 75 kW hingga lebih 400 kW bergantung pada saiz; compatible with VFDs for soft start and speed control.
Spesifikasi Bahan: Contact surfaces utilize MNF A514 abrasionresistant steel (min. BHN 400), highalumina ceramic liners (>85% Al₂O₃), or cast NiHard alloys as application dictates.
Dimensi Fizikal: Kejuruteraan tersuai bagi setiap susun atur loji; typical separator diameters range from 3m to over 7m.
Julat Operasi Persekitaran: Direka untuk suhu ambien dari 20°C hingga +45°C, handling process gas temperatures up to 400°C (taufan) and product temperatures up to 120°C (pemisah).

6. SENARIO APLIKASI

Plant Capacity Upgrade & Efficiency Retrofit

Cabaran: A regional plant needed to increase output by 15% while reducing its overall specific energy consumption to meet new corporate targets.
Penyelesaian: Replacement of existing firstgeneration cyclones with a modern lowpressure drop preheater stage and installation of a highefficiency dynamic separator on the finish mill circuit.
Keputusan: Tercapai a 16% throughput increase with a simultaneous reduction of total electrical energy consumption by approximately kWh/tonne clinker.

Product Flexibility Enhancement

Cabaran: A grinding station supplying multiple markets struggled with slow changeovers between different cement types (mis., OPC vs PPC), losing hours of production time.
Penyelesaian: Installation of an advanced dynamic rotor separator with automated online adjustment controls linked directly to the plant’s Blaine analyzer.
Results Reduced product grade changeover time from several hours down minutes enabling flexible response market demand without significant throughput penalty

7 PERTIMBANGAN KOMERSIL

Equipment pricing structured around capacity size customization level Standard packages are available for brownfield retrofit projects while greenfield installations require full custom engineering Optional features include advanced ceramic composite linings remote monitoring integration packages extended lubrication systems

Service packages offered as tiered solutions:
asas: Includes commissioning supervision oneyear parts warranty
Premium: Adds annual health inspections predictive maintenance analysis training for onsite teams
Platinum: Comprehensive longterm performance agreement covering scheduled parts replacement guaranteed availability

Financing options available through partnered institutions can include leasetoown structures milestonebased project financing tailored support major capital expenditure programs

8 Soalan Lazim

What is lead time typical order?
Lead times vary based project complexity For standard designs minimum order quantity typically single unit per system e g one separator string cyclones Lead times range from months full engineering manufacturing

How ensure new equipment compatible existing plant PLC DCS?
Our engineering team conducts preorder interface review requiring your system specifications All equipment supplied with standard communication protocols Profibus Modbus TCP typically interface seamlessly with higherlevel control systems

What quantifiable efficiency gains can expect?
Based field data installations can expect reduction specific power consumption milling circuit range improvement thermal efficiency preheater tower through reduced pressure drop Detailed projections provided during technical proposal phase

What included standard commissioning?
Standard commissioning includes supervisor presence during installation mechanical check initial startup performance testing ensure design parameters met does include major electrical civil works required site

Are spare parts kits available?
Yes recommended initial spare parts kits offered containing critical wear items gasket sets sensor modules based predicted consumption rates ensure minimum stocking onsite

What warranty period provided?
Standard warranty covers defects materials workmanship period months from commissioning date operational hours whichever comes first Extended warranties available under Premium Platinum service agreements